Guide / MED17 ECU / Main Patch Map Switch

Main Patch Map Switch

Map switching for Bosch MED17 ECUs: two to five map slots, selected from the cruise control stalk, the ESC button or the turn signal lever. Each slot carries its own torque limit, boost limit and driver-requested torque map, plus a spark offset on MED17.5, and switches Launch Control, rolling anti-lag and pops & bangs on or off.
Available for these software versions:

• MED17.5 (1.8 / 2.0 TFSI): D175X55H_M08S14, D175X55H_M08W20, D175X55H_M08Z20, D175X55H_M08Z40, D175X55H_M08Z50, D175X56H_M09G10, D175X56H_M09G20, D175X56H_M09G30, D175X56H_M14F31, and the Bosch software numbers 1037396225 and 1037507917
• MED17.5.2: D1752V02C000_MY13E31, D1752V07C000_MY13E01, D1752V08C000_MY11H41
• MED17.5.21: D17521V36C002_M28I9C
• MED17.1.27 (EA211): D17127V50C001_M33V52
The patch is available in the Tune Editor. Flashing MED17 ECUs with simos.app is coming soon.

Contents

Map switching

Number of map slots (2..5) sets how many slots UP and DOWN browse through — anywhere from two to five. A value outside that range uses all five.
Selecting a slot
Hold the button assigned to Map switching — CANCEL by default — for Hold time to open map selection. A short press does nothing. Once the hold completes, the rev counter shows the current slot. UP and DOWN (SET+ and SET−) step through the slots, SET commits immediately. 0 uses the default of 2000 ms.
Selection window — the idle time after which the displayed slot is committed. The timer restarts on every UP or DOWN press. 0 uses the default of 3000 ms.
Shared axes
The torque limit maps of all slots share one rpm axis, Torque limit: rpm, and the boost limit maps share Boost limit: rpm. Both must be rising. The spark offset uses the rpm and load axes of the stock basic ignition map.

Button assignment

The cruise control buttons can be pointed at the map switch or at rolling anti-lag. The ESC button and the turn signal lever can also open map selection.
CANCEL button — Off, Map switching or Rolling anti-lag. Default: Map switching.

RESUME button — the same three options. Default: Rolling anti-lag.

SET button — the same three options. Default: Off.

UP and DOWN always step through an open selection, and SET always confirms it.
ESC button — None or Mapswitch double tap. Tap ESC twice within the ESC double-tap window (default 1000 ms) to open map selection, then tap once per slot to step through them. The shown slot is committed after the selection window. The taps also switch traction control as usual. Default: None.
Turn signal lever — None or Mapswitch. With the ignition on and the engine not running (below 100 rpm), tap the indicator left, then right within 2 s, to open map selection. Right steps to the next slot, left to the previous one, and the shown slot is committed after the selection window. It works without cruise control. Default: None. Not available on D175X55H_M08S14, 1037396225 and 1037507917.

What each map slot holds

Every slot is a complete configuration of its own rather than an offset from a base map.
Torque Limit by rpm and gear — a ceiling on the engine's indicated torque in Nm, by rpm and gear (row 0 = neutral and reverse, row 1 = first gear; gears above 7 use the last row). It is applied to the ECU's own torque limit for both the ignition and the air path, so boost and timing follow it together. It only ever lowers torque: the lower of the ECU limit and the map wins. Full scale (3276.7 Nm, as shipped) means no limit. Not available on 1037396225.
Boost pressure limit by rpm and gear — a ceiling on the boost pressure setpoint, absolute pressure in bar, by rpm and gear. The boost controller regulates to the capped setpoint. It never raises boost, and full scale (as shipped) means no limit.
Driver Requested Torque (slots 2 to 5) — a pedal map in Nm by engine speed and accelerator pedal. With the slot's Driver Requested Torque override On, it replaces the stock pedal maps; reverse and maps that are empty in stock always stay stock. Off keeps the stock maps. Slot 1 always uses the stock pedal map.
Spark offset (MED17.5 only) — an ignition trim added to the basic ignition angle by rpm and load. Positive advances, negative retards, 0 is stock timing, limited to ±22.5°.
Per-slot switches
Launch Control arms Launch Control in this slot, RAL arms rolling anti-lag, and Pops & bangs with Pops duration and Pops intensity sets the overrun crackle — see Pops & bangs. All three are off by default.

Launch Control

Launch Control holds the revs on the line with a rotating injection cut and a retarded ignition angle. It arms at a standstill with the brake or clutch held and the throttle floored, in a slot with Launch Control switched on.
Max rpm — the engine speed held during the launch. The injection cut steps in over the 200 rpm below it: one cylinder within 200 rpm, two within 100 rpm and the heaviest cut within 50 rpm, so the revs settle at Max rpm. 0 turns launch off.

Ignition angle — the ignition angle held during the launch. Negative is retarded, after TDC: later means less torque on the line and more crackle.
Arming
Max speed to arm — launch only arms below this road speed, so it is a standing-start feature and cannot be triggered while rolling. 0 means at a dead standstill only.

Minimum oil temperature and Minimum coolant temperature — launch will not arm on a colder engine.

Rolling anti-lag (RAL)

Rolling anti-lag combines a retarded ignition angle with a fuel cut to keep the turbo spooled on the move. It engages while the button assigned to Rolling anti-lag is held — RESUME by default — in a slot with RAL switched on.
Trigger hold time to engage — how long the button must be held before anti-lag engages, so a normal tap does not trigger it. RAL stays active while the button is held, up to Maximum active time, and ends as soon as it is released.

Maximum active time — a safety cap per hold. On timeout RAL disengages until the button is released and held again. 0 means no time limit.

Minimum rpm and Maximum rpm — the engine speed window in which the trigger is accepted, checked when RAL engages. A Minimum rpm of 0 means RAL never arms.

Minimum oil temperature and Minimum coolant temperature — RAL will not engage on a colder engine.

Ramp-in time and Ramp-out time — how long the ignition retard takes to fade in and out. 0 is immediate.
Ignition retard
On MED17.5, Ignition retard vs EGT sets the retard by measured exhaust gas temperature, so it can be backed off as the temperature climbs to protect the exhaust and turbine. Maximum ignition retard caps it. MED17.5.2, MED17.5.21 and MED17.1.27 have no exhaust gas temperature signal, so a single Ignition retard value applies in every slot.

Pops & bangs

On a throttle lift-off the overrun fuel cut is held off for a short burst and the ignition is pulled late, so fuel burns in the exhaust. It runs in slots with Pops & bangs switched on, which also arms the after-shift pops.
Per slot
Pops duration — burst length as % of the Pops duration map. 100 % is unchanged, higher gives a longer crackle, 0 % is off.

Pops intensity — how far the ignition is pulled late, as % of the Pops ignition angle map. 100 % is unchanged, higher is louder, 0 % adds no extra retard. Never later than −54°.
When pops fire
Off-throttle pedal threshold — a burst starts when the pedal drops to or below this position.

Re-arm pedal threshold — pressing the pedal to at least this position ends a running burst and re-arms pops for the next lift-off.

Minimum rpm and Maximum rpm — the engine speed window. A running burst ends when the revs drop below the minimum.

Minimum speed — no pops below this road speed while a gear is engaged.

Minimum coolant temperature — no pops on a cold engine.

Pops in Neutral/Park — On allows pops in Neutral and Park, standing or rolling, using the gear 0 row of the maps. Off means no pops in Neutral or Park.
Maps
Pops duration and Pops ignition angle set the burst length and the ignition angle by gear (row 0 = Neutral/Park) and engine speed. A duration of 0 means no pops in that cell. The OEM angle is used if it is already later, and the angle is limited to −54°. All pops maps share the Engine speed axis, which must be rising.
After-shift pops
A short burst after every gear change between two forward gears, up or down, with DSG and manual gearboxes — never into or out of reverse or Neutral/Park. After-shift pops duration and After-shift pops retard are mapped by the new gear and the engine speed at the change. The retard only ever pulls the ignition later, so it never adds torque, and any torque reduction the gearbox requests stays in place.

After-shift pedal threshold (upshift) — an upshift only pops after a shift under load, with the pedal at least this far down shortly before the new gear. Downshifts ignore it.

After-shift max shift time — the longest time from leaving the old gear to the new one that still counts as one gear change.

After-shift minimum rpm and After-shift maximum rpm — the engine speed window at the gear change, so normal low-rpm shifts while coasting stay quiet.

Drive mode profile (MED17.1.27)

On MED17.1.27 (D17127V50C001_M33V52) the active slot can also follow the drive mode selected in the car.
Map follows drive mode — On loads the slot set for the current profile: Normal / Auto, Sport / Dynamic and Eco / Efficiency, each set to Map 1 to Map 5 or to No change. Other drive modes keep the current map. The cruise stalk selection still works, and a map picked by hand stays until the drive mode changes again. Default: Off.
This ECU also has separate Sport versions of the pops and after-shift pops maps, used while the Sport drive mode is selected.

VIN lock

Each tune is bound to one vehicle through a fingerprint of its VIN, set automatically when the patch is applied — it is not edited by hand. Until the fingerprint is set, or if it does not match the car's VIN, map switching, spark offset, torque and boost limits, Launch Control, rolling anti-lag and pops all run stock.

Flashing the patch

Adding or removing a patch requires a Full Flash. Changing the parameters afterwards is calibration only and goes out as a CAL Flash — see CAL Flash and Full Flash.
Flashing MED17 ECUs with simos.app is not available yet and is coming soon — see compatibility.