Guide / Simos 18 ECU / Stage 1
Simos 18 · Simos 12.x · Tuning guide

Simos 18 & 12 Stage 1 Tuning

What to change for a Stage 1 tune on Simos 18 and Simos 12.x, in the order the ECU uses it: the torque model, the torque request, boost, air mass limits and ignition. Both use the same maps.
  • 5 steps
  • Torque ↔ Airflow wizard
  • IS12 · IS20 · IS38
Before you start

How torque becomes boost

Simos 18 and Simos 12 are torque based. The pedal does not ask for boost, it asks for torque, and the ECU works its way from there to an air mass and a boost pressure. Every stage has limits of its own, and a Stage 1 tune raises them in this order.
  1. 1
    Pedal
    0–100 %
    How far you press the accelerator.
  2. 2
    Pedal Map
    % → %
    Torque Request › Pedal Map converts the pedal position into a share of the maximum torque.
  3. 3
    Max Clutch Torque
    Nm
    That share is taken from the current maximum torque. The result is the torque request.
    Limits
    ip_tq_pow_max_atip_tq_pow_max_mtip_tqi_pow_max_basid_tq_sp_maxip_tqi_ref_max_monip_tq_lim_gb_prot_max_*
  4. 4
    Torque to Airflow
    Nm → mg/stk
    Torque Model › Torque to Airflow turns the torque request into an air mass per stroke.
    Limits
    c_m_air_cyl_sp_maxip_m_air_cyl_max_stnd_vvl
  5. 5
    Boost
    hPa absolute
    The ECU tries to reach that air mass, for example by closing the wastegate.
    Limits
    ip_put_spc_prs_im_sp_limc_prs_im_sp_maxip_pq_cha_max
01Wizards › Torque ↔ Airflow Model

Extend the torque model

Start here. Open Wizards in the tune editor, choose Torque ↔ Airflow Model and apply it with its default values, as long as Max torque is above your torque target. If your target is higher, raise Max torque above it first.

The wizard extends every map in both groups beyond stock load, for each valve lift and cam position and both port flap positions. The two groups should be linear and the inverse of each other: the torque Airflow to Torque calculates for an air mass, Torque to Airflow has to turn back into the same air mass.
Why it matters
Wrong model values lead to poor shifts on DSG cars, and to wrong torque and power figures in your logs and in the app.
Map groups the wizard changes2 entries
  • Torque Model › Airflow to Torque - Port Flap High / Low
    ip_tqi_ref_n_m_air_vvl_cam_h / _l
    mg/stk → Nm
  • Torque Model › Torque to Airflow - Port Flap High / Low
    ip_maf_stk_sp_vvl_cam_h / _l
    Nm → mg/stk
02Torque Request › Max Clutch Torque

Set the torque request

Max Clutch Torque › AT / MT is the most torque the pedal can ask for at each engine speed. Raise it towards your target, but follow the curve your turbo can actually deliver:

• IS12: torque comes in early, then flattens off
• IS20: strongest in the midrange
• IS38: comes in later than the IS20, then flattens off as well
More request is not more torque
If the turbo cannot deliver more air, there is no more torque. Because the pedal is a percentage of this map, a request far above what the turbo can make costs pedal precision: a large part of the pedal travel asks for torque the engine never reaches, and the car feels bad to drive.

Better: log with a little more torque than is possible, then set realistic values for each engine speed that do not run into limits such as turbo speed, turbo outlet temperature and pressure difference.
Maps2 entries
  • Max Clutch Torque AT
    ip_tq_pow_max_at
    DSG and automatic
    your torque curve
  • Max Clutch Torque MT
    ip_tq_pow_max_mt
    Manual gearbox
    your torque curve
Torque limits

Move the torque limits out of the way

These maps only cap torque. Set them well above your target so they never limit.

The gearbox protection maps only exist in some versions. Set them to 1000 Nm or anything above your torque target, or switch the protection off entirely with Clutch Protection Limit.
Limits6 entries
  • Base Max Indicated Torque
    ip_tqi_pow_max_bas
    1000 Nm
  • Curve to define maximum torque: Input GEAR
    id_tq_sp_max
    Not in every version
    1000 Nm
  • Max Indicated Torque (Monitoring)
    ip_tqi_ref_max_mon
    Limiter › Monitoring, needs the ECM3 checksum
    1000 Nm
  • Max Clutch Torque DCT / MT / MT 4WD / AT / CVT
    ip_tq_lim_gb_prot_max_dct, _mt, _mt_4wd, _at, _cvt
    Gearbox › Transmission Protection, some versions
    1000 Nm
  • Clutch Protection Limit
    lc_tq_clu_prot_max_ena
    Alternative to raising the five maps above
    Off
  • Indicated engine torque at reference conditions
    ip_tqi_ref_n_m_air
    If the last row is below your target torque, raise it so the curve continues. Only a limit, so it does not have to match the torque model.
    continue the curve
03Airflow › PUT Setpoint

Raise the boost request

PUT Setpoint sets the pressure the ECU asks for upstream of the throttle. Its last row is the maximum, and the table should stay linear. All values are absolute pressure.

Three more limits have to fit that maximum. Turbo Max Pressure Ratio works over engine speed and intake air temperature: keep it close above your PUT Setpoint, so it still limits boost when the intake air gets hot.
Maps4 entries
  • PUT Setpoint
    ip_put_sp
    Linear, absolute pressure
    last row = max
  • Maximum Intake Manifold Pressure
    c_prs_im_sp_lim
    = max pressure
  • Maximum Requested Intake Manifold Pressure
    c_prs_im_sp_max
    a little below
  • Turbo Max Pressure Ratio
    ip_pq_cha_max
    Safety limit for hot intake air
    a little above
04Limiter

Lift the air mass limits

Two more limits cap the air mass per cylinder stroke. The second one works over engine speed, with one curve per valve lift profile, so change both curves.
Limits2 entries
  • Maximum allowed M_AIR_CYL_SP
    c_m_air_cyl_sp_max
    2000 mg/stk
  • Maximum intake air at standardized ambient pressure
    ip_m_air_cyl_max_stnd_vvl[0] / [1]
    From 1500 to 2000 rpm upwards
    2000 mg/stk
05Spark › Base

Adjust ignition

The base ignition angle lives in two groups, one per port flap position. Each group has 18 maps, one for every combination of valve lift (VVL 0 and 1), intake cam and exhaust cam position. This is where you add or remove timing.
Log and watch for knock
Log a pull after every change and look at knock retard.

• No knock at all: add about 3° and log again
• Occasional retard of 1 to 3°: that is fine
• Around 3° retard all the time at full load: take 2 to 3° back out
Map groups2 entries
  • Spark › Base - Port Flap High
    ip_iga_bas_ivvt_vvl_port_h[0..1][0..2][0..2]
    Basic Ignition Angle VVL 0/1, Intake 0–2, Exhaust 0–2
    18 maps
  • Spark › Base - Port Flap Low
    ip_iga_bas_ivvt_vvl_port_l[0..1][0..2][0..2]
    Basic Ignition Angle VVL 0/1, Intake 0–2, Exhaust 0–2
    18 maps